PPF Install Guide

Clif Designs

PAINT PROTECTION FILM INSTALL GUIDE

1. Tools & Solutions

A. Tools

●  Clay Pad & Bar

>>> A clay bar is recommended over a clay pad. If you use a clay pad, we recommend the soft type.

>>> Always use with a soap mix (the soap ratio should be higher than your install mix).

●  Squeegee

>>> A urethane squeegee is recommended to avoid scratching or damaging the film. Use felt if you use a plastic hard card.

>>> Medium hardness. A hard squeegee can put too much pressure on the film and cause problems. A soft squeegee may not remove all the water and can leave water spots longer after install.

>>> A 3" to 5" squeegee you can hold easily in one hand is recommended.

●  Knife & Blade

>>> A light, thin body is better for precise cutting.

>>> A 30° carbon steel or ceramic blade is recommended for precise cutting.

●  Spray Bottle

>>> A sprayer with large droplets, high volume and a wide spray angle is recommended.

●  Heat Gun

>>> A heat gun with temperature control gives a more consistent finish.

B. Solutions

●  Water

>>> Distilled water is the best option. Use purified water if distilled water is too expensive or hard to get.

>>> Water temperature affects film stretch and adhesive strength. 77°F (25°C) is generally right. When your shop is colder than that, use water at 86°F to 95°F (30°C to 35°C). When your shop is hotter, use water at about 72°F (22°C).

●  Degreasing

>>> Used to remove oil from the vehicle surface before install.

>>> Clif Designs Quick Surfer degreaser is recommended.

>>> 70% isopropyl alcohol is an alternative if Quick Surfer is not available.

●  Squeegee Solution

>>> Lets the squeegee glide smoothly over the film surface.

>>> Starting mix: water and Johnson's Baby Shampoo at 1 liter to 4 drops. Adjust for your shop temperature and the film.

>>> Use 1 drop less when your shop is colder than 77°F (25°C) and 1 drop more when it is hotter.

>>> Hydrophobic films, including matte, need 1 more drop than the starting mix.

●  Adhesive Solution

>>> Sprayed on the film adhesive and the vehicle so the adhesive does not grab the vehicle while dry.

>>> An install gel such as Clif Designs Moister is recommended.

>>> When using install gel, add 1 drop of shampoo when your shop is hotter than 77°F (25°C).

>>> Squeegee solution can be used in place of install gel.

●  Cleanse

>>> Rinse the adhesive solution from the film edges after squeegeeing so the adhesive regains its full strength.

>>> Rinse with water at the right temperature as much as possible. A shower hose works better than a spray bottle.

>>> If you do not have a hose in your shop, use 30% isopropyl alcohol and 70% water.

>>> Alcohol also makes water evaporate faster, which activates the adhesive sooner. Too strong a mix can affect the adhesive and haze the film.

2. Working Environment

●  Work indoors, out of direct sunlight, and keep dust to a minimum.

●  Keep the shop as bright as possible. Use tri-phosphor LED lighting if you use artificial light.

●  At 77°F (25°C) the film stretches well and the adhesive behaves normally.

>>> In a colder shop, use warm water. The film stretches less and the adhesive gets weaker.

>>> In a hotter shop, control your water temperature and adhesive solution. The film stretches easily, but the adhesive can grab too hard.

3. Pre Installation

●  Remove all grease, stains and dirt from the vehicle. This is essential for a clean install. It affects adhesion and debris under the film, and degreasing directly affects adhesive strength and edge lift after the edges are finished.

●  Degreasing and Cleaning

>>> Step 1. Wash the surface with a high pressure nozzle. Watch the water temperature for your shop conditions.

>>> Step 2. Use a clay pad or bar to remove anything left after step 1. Then repeat step 1 and dry completely.

>>> Step 3. Wipe the install area with degreaser on a dry buffing towel. If the towel gets too wet, switch to a fresh one.

4. Installation

●  Use the solutions in order: Adhesive Solution, then Squeegee Solution, then Cleanse.

●  Spray the Adhesive and Squeegee Solutions with a wide angle nozzle, and use plenty.

●  The Cleanse rinse needs strong water pressure, not a wide spray. Use your finger to rinse the film edge with the spray. (See the picture.)

Adhesive & Squeegee Solution Cleanse Solution

●  Do not overstretch the film. Overstretching can crack the top coat, make the film get dirty faster, and weaken its self healing and stain resistance.

●  Squeegeeing

>>> Hold the squeegee at a 60° angle, not straight up. (See the picture.)

BAD 60° GOOD

>>> Squeegee from the inside out. (See the picture.)

BADGOOD

>>> Do not stop the squeegee in the middle of a stroke. On large areas, push from the inside out while moving the squeegee naturally upward. Stopping can leave a line where the squeegee stopped.

●  After the Cleanse rinse, wait 3 to 5 minutes for the edges to dry. The edges are easier to finish.

●  Wrap the edges so the finish line does not show. Keep the wrap as short as you can, since a long wrap can lift. (For a hood, about 3 mm / 0.12".)

●  Heat the edges to prevent lift. The right temperature is about 390°F (200°C). After the heat gun passes slowly, press the film with your finger (wear heat resistant gloves) or a felt hard card.

5. Removing Film

●  Check whether the paint was refinished before the PPF went on. Paint can peel off with the film if the PPF was installed over a repaint after an accident.

●  If the shop is colder than recommended, the film and adhesive layers can separate easily. Keep the shop at the recommended temperature.

●  Film comes off more easily with heat. Heat to about 570°F (300°C) and remove the film a little at a time, about 7" (20 cm) at a step.

●  Do not fold the film back on itself. Lift it and pull it off at a low angle. (See the picture.)

Pull direction>60°BADPull direction45°GOOD

6. Care After Installation

●  Do not wash the vehicle for 72 hours after install. Allow longer in winter.

●  Water bubbles after install will go away on their own over time. Do not press them or push them with your finger.

●  Regular hand washing is recommended. Mild soap and a soft cloth are fine.

●  Do not point a pressure washer directly at the film edges from closer than 17" (45 cm). It can lift or puncture the film.

●  After washing, Clif Designs Vitalizer top coat care is recommended.

●  Wipe off rain spots and stains as soon as you can.

●  Polishing with a soft foam pad can be done every two years to remove old stains, and the film returns to its original clarity. Polishing thins the top coat, so the film may get dirty and wear faster afterward. We recommend Clif Designs Vitalizer.

DK Distributing

Questions? Contact us


www.dkdistributing.com

Clif Designs

Shop Install Chemicals